printrbotJr-slic3r-config.ini

# Tested specifically for Faberdashery Arctic White PLA 3mm dia. filament

# Note the Z and E calibrations are a little different from the defaults suggested in the printrbot getting started guide (http://printrbot.com/wp-content/uploads/2012/04/Printrbot-Getting-Started-Guide2.pdf) as I think these may vary between one machine and another

# generated by Slic3r 0.9.5 on Sat Dec 15 15:23:15 2012
acceleration = 0
bed_size = 120,120
bed_temperature = 0
bottom_solid_layers = 3
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
complete_objects = 0
cooling = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors
external_perimeter_speed = 50%
extra_perimeters = 3
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 3
fill_angle = 45
fill_density = 0.4
fill_pattern = rectilinear
first_layer_bed_temperature = 0
first_layer_extrusion_width = 200%
first_layer_height = 100%
first_layer_speed = 50%
first_layer_temperature = 185
g0 = 0
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 40
layer_gcode =
layer_height = 0.4
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes =
nozzle_diameter = 0.5
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 25
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 2
post_process =
print_center = 60,60
randomize_start = 1
retract_before_travel = 2
retract_length = 1
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 4
slowdown_below_layer_time = 15
small_perimeter_speed = 15
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_speed = 30
start_gcode = G28 ; home all axes\nM92 X64.8592 ; calibrate X\nM92 Y64.8592 ; calibrate Y\nM92 Z2170.0654 ; calibrate Z\nM92 E502.0588 ; calibrate E
support_material = 0
support_material_angle = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_threshold = 45
temperature = 185
threads = 2
top_solid_infill_speed = 30
top_solid_layers = 3
travel_speed = 195
use_relative_e_distances = 0
z_offset = 0

Leave a Reply